Mold making basics: Silicone Block Mold
Block mold explanation. This is the most basic mold method for silicone rubber. This is a good method when speed is more important than overall cost. We used 73-45 platinum silicone for this particular mold. A cut block mold like this works best with rubber that is shore A20 or higher. This means...
Mold Making and Casting: Casting R2 Rigid Foam
Here are 2 methods for achieving a good matte, paintable surface on rigid, urethane foam. Both baby-powder and primer (sprayed into the mold and allowed to dry) may be used to create a cast part with a matte surface for easy painting. New Prime-it primer may also be used to simplify the painting ...
Mold Making With Glove Mold Process
Mold making process using a seamless glove mold made with Platsil Gel-10. This is a great process for molding simple figure sculpts or portrait busts. Gel-10 is stretchy enough to pull inside out over some basic forms. The finished mold may be used for resin casting, plaster casting, or hydroston...
Plastic Injection Mold Making
Mountain Mold & Die, Inc. 127 River Bend Drive Sevierville, TN 37876 www.mtnmold.com 865-428-3611
Mold Making - Mass Casting Complex Parts (w/ parting line)
When mass casting a part without a flat side, you must create a two-part mold. We create a two-part silicone rubber mold with a clean parting line and then cast the part with Repro.
How to make a two-part mold
This video segment will show you how to make a simple two-part mold using Urethane RTV molding rubber.
tapplastics- Length: 4:51
- Views: 914335
- Tags: tap plastics two-part mold molding urethane rtv mold-making rubber
-
Mold Making Face Cast With 880 Alginate
Lifecast mold making with 880 from Accucast. I put my shaved head to good use and did an open mouth lifecast mold with no bald cap. This is a VERY truncated version of a lifecast. The complete process is explained on our Lifecasting 101 DVD.
Mold Making and Casting: Cold Casting resin with metal powders
This is another approach to cold casting. We dusted a 71-20 silicone mold with metal powders and then we cast EZ Flo resin behind to create a realitic, metalic cast. Just a little bit of polishing with 0000 steel wool reveals a beautiful metal finish on the resin surface.
Martha Stewart uses OOMOO 30 to Make a Candle Making Mold
Martha Stewart uses OOMOO 30 silicone rubber from Smooth-On to make candle molds and cast wax with Kelly Ripa. For more information, visit www.smooth-on.com Make It Now! with Smooth-On www.smooth-on.com www.facebook.com twitter.com
- smoothoninc
- Length: 9:55
- Views: 47759
- Tags: mold making casting how to tutorial martha stewart candle making silicone kelly ripa smooth on smoothon smooth-on molding moldmaking diy
-
Mold Making: Basic Block Silicone Mold
Here's a set of block molds made using 71-20 silicone. This is an overview of the mold making and casting process.
Types of RTV Mold Rubber for Mold Making and Casting, Pros & Cons
www.smooth-on.com to see more video tutorials and image galleries. Examining the different types of RTV mold rubber available for mold making and casting from Smooth-On. Advantages of Latex * Least expensive mold rubber available. * Very elastic, thin-walled and strong. * Lasts a long time. * Off...
- smoothoninc
- Length: 8:27
- Views: 100776
- Tags: mold making casting how to tutorial rtv silicone silicone urethane rtv urethane rubber rtv rubber smooth on liquid rubber liquid silicone urethane rubber mold making materials smoothon smooth-on molding moldmaking diy latex polysulfide pros and cons advantages disadvantages
-
Mold Making for Precious Metal Clay
Making molds for precious metal clay is easy. Using RTV mold materials such as MegaMold and Sculpey Mold Maker, you can make low cost molds from almost anything you want to pick up texture from or duplicate.
Mold Making - Urethane Rubber Molds
Urethane Rubber molds are widely used when a flexible mold material is required and a more expensive or less abrasion-resistant silicone rubber is not desired. However, their use requires careful application of release agents.
Mold Making and Resin Casting Your Own Sculpted Miniatures - Part 1
Part 1 of a Video Series that details how to make Rubber Molds and Resin Casts of your own 28mm Miniatures. The casting kits used is Smooth-On's Mold Making and Casting Pourable Starter Kit. Smooth-On's Website: www.smooth-on.com (Also check out their great Mold and Cast videos!) Apparently on Am...
Mold Making: 2 piece mold
2 piece Silicone mold made with PlatSil 73-15. We used a plywood frame to make a 2 piece silicone mold for casting EZ Flo 60 prop scissors. Mold was made with low viscosity platinum silicone.
Mold Making for Wood Carvings, Reproducing a Wood Grain Finish
www.smooth-on.com for more sculpture and art mold making demonstrations. When making molds of wood carvings, it is important to be able to reproduce the woodgrain. Dragon Skin 10 will pick up detail down to a fingerprint. In addition, cured Dragon Skin 10 is very strong and very stretchy. It will...
- smoothoninc
- Length: 4:06
- Views: 8735
- Tags: mold making molding moldmaking smooth on smoothon smooth-on casting how to tutorial diy wood carvings wooden model wood sculpture silicone mold dragon skin 10
-
Making a Brush-On Silicone Mold | Mold Making Tutorials, Part 1/2
www.smooth-on.com for more information about Smooth-On silicone rubbers. Making a Brush-On Mold with Rebound 25 Liquid Silicone Rubber (Part 1 of 2) For this demonstration we are going to use a small plastic model. Step One: Secure Model to Baseboard Hot-melt glue is used to secure model to baseb...
- smoothoninc
- Length: 7:13
- Views: 95142
- Tags: silicone rubber silicone mold silicone molds liquid rubber liquid silicone silicone molding mold making casting smooth on silicone smoothon smooth-on brush on mold molding moldmaking diy
-
Reusable Mold Making Material, Making parts without the cost.
Here is a short demonstration of the use of ComposiMold. Low cost, easy to use, and reuse. ComposiMold is a reusable mold making material that works by melting and pouring. Many casts can be performed using the same mold. ComposiMold is good for the mold maker and craft artist because it can be r...
- composimold
- Length: 0:51
- Views: 21554
- Tags: plaster casting urethane casting mold making mold making demonstration do it yourself molding how-to craft
-
Custom Chocolate mold making with ComposiMold
Simple method to make custom chocolate molds that can be continuously reused for new molds and castings To order directly visit: compositherm.com For more information visit www.composimold.com
- composimold
- Length: 4:47
- Views: 11883
- Tags: chocolate molds chocolate casting chocolate mold making composimold Chocolate molding
-
Mold Making and Resin Casting Your Own Sculpted Miniatures - Part 2
Part 2 of a Video Series that details how to make Rubber Molds and Resin Casts of your own 28mm Miniatures. The casting kits used is Smooth-On's Mold Making and Casting Pourable Starter Kit. Smooth-On's Website: www.smooth-on.com (Also check out their great Mold and Cast videos!) Apparently on Am...
Page: 1 of 2172
